1.采用變頻控制，啟動平穩，分離因數可調。

2.吊袋卸料，晶粒不易破碎；勞動強度低，工效高；通用性強，適用范圍廣。

3.結構設計合理，結構件圓滑過渡，表面拋光處理，無衛生死角。翻蓋式外殼，可對外殼與轉鼓夾層空間進行徹底清洗。

4.機座與機殼為整體焊接結構，承載強度高。

5.平板式機座，機器重心低，占地空間小，平板機座可作為操作平臺，操作方便。

6.四點支撐液態阻尼減振器，減振效果好，簡化日常保養。

7.外殼翻蓋設置進料管、洗滌管、觀察鏡、照明孔等常規管口。

8.配置在線清洗系統(選裝)，可對離心機外殼內壁、轉鼓內外表面、集液槽表面等內部不可見部位進行清洗，保證了潔凈度要求，符合GMP規范。

9.密閉結構，密封件采用硅橡膠或氟橡膠，配置氮氣保護系統(選裝)，可實現密閉防爆要求，適合于有毒和易燃易爆場合的應用。

10.配置液壓式懸臂吊(選裝)，卸料方便，符合衛生要求。

1. Adopt frequency conversion control, start smoothly, separation factor can be adjusted. 

2. The hanging bag unloading, the grain is not easy to break; the labor intensity is low, the work efficiency is high; the versatility is strong, the scope of application is wide. 

3. Reasonable structure design, smooth transition of structural parts, surface polishing treatment, no sanitary dead angle. 

Flip shell, can thoroughly clean the shell and drum sandwich space. 

4. The base and shell are welded as a whole, and the bearing strength is high. 

5. Flat machine base, low center of gravity of the machine, small space occupied, flat machine seat can be used as an operating platform, easy to operate. 

6. Four-point support liquid damping shock absorber, good damping effect, simplify daily maintenance. 

7. The shell flip is provided with a conventional pipe mouth such as a feed pipe, a washing pipe, an observation mirror, an illumination hole, etc. 

8. Equipped with on-line cleaning system (optional), the inner wall of centrifuge shell, the inner and outer surface of drum, the surface of liquid collecting tank and other internal invisible parts can be cleaned, which ensures the cleanliness requirements and conforms to GMP specification. 

9. Sealed structure, sealed with silicone rubber or fluorine rubber, equipped with nitrogen protection system (optional), can achieve closed explosion-proof requirements, suitable for toxic and flammable and explosive applications. 

10. Equipped with hydraulic cantilever crane (optional), easy to discharge, in line with health requirements.

待分離的物料經進料管進入高速旋轉的離心機轉鼓內，在離心力場的作用下，物料通過濾布（濾網）過濾，液相經出液管排出，固相則截留在轉鼓內。待轉鼓內濾餅達到機器規定的裝料量時，停止進料，對濾餅進行洗滌，同時將洗滌液濾出。

濾餅脫液達到要求后，停機。專用的吊具將濾袋連同濾餅一起吊出至指定卸料處，打開卸料口，將濾餅卸出，然后將濾袋復位，進入待機狀態。

The material to be separated enters the high-speed rotating centrifuge drum through the feed tube. under the action of the centrifugal force field, the material is filtered through the filter cloth (filter net), the liquid phase is discharged through the outlet tube, and the solid phase is intercepted in the drum. 

When the filter cake in the rotating drum reaches the loading quantity specified by the machine, the feed is stopped, the filter cake is washed, and the washing liquid is filtered out at the same time. 

After the filter cake is removed from the liquid to meet the requirements, stop. 

The special hoist will lift the filter bag together with the filter cake to the designated discharge place, open the discharge port, unload the filter cake, and then reset the filter bag and enter the standby state.

用于固相為顆粒狀的懸浮液的固液相分離，也可用于纖維狀物料的固液相分離。

如：石膏、硫酸銅、氯化鉀、硼砂、染料、農藥藥劑，食鹽、味精、食品添加劑、淀粉、制糖、化學調味料，抗生素、維生素，銅、鋅、鋁等礦產物、金屬精制，污泥處理、污水處理等。

It can be used for solid-liquid phase separation of solid-liquid suspension with granular solid phase, and can also be used for solid-liquid phase separation of fibrous materials. 

Such as gypsum, copper sulfate, potassium chloride, borax, dyes, pesticide agents, salt, monosodium glutamate, food additives, starch, sugar, chemical condiments, antibiotics, vitamins, copper, zinc, aluminum and other mineral products, metal refining, 

Sludge treatment, sewage treatment, etc.